NAD C 368
Key Features
80W x 2 Continuous power into 8 or 4 Ohms
Bluetooth A2DP with aptX supported
MM Phono input
Stereo or Bridge mode configuration
Preamp/Subwoofer out
Headphone amplifier
Key Features
80W x 2 Continuous power into 8 or 4 Ohms
Bluetooth A2DP with aptX supported
MM Phono input
Stereo or Bridge mode configuration
Preamp/Subwoofer out
Headphone amplifier
Key Features
80W x 2 Continuous power into 8 or 4 Ohms
Bluetooth A2DP with aptX supported
MM Phono input
Stereo or Bridge mode configuration
Preamp/Subwoofer out
Headphone amplifier
PRODUCT DETAILS
Preamplifier
Line Input, Pre Out
THD (20Hz-20kHz)- <0.005% at 2V out
Signal/Noise Ratio- >106dB (IHF; A-weighted, ref. 500mV out, unity gain)
Channel Separation- >80dB (1kHz); >70dB (10kHz)
Input Impedance (R and C)- 22 kilohm + 100pF
Maximum Input Signal- >4.5Vrms (ref. 0.1% THD)
Output Impedance- Source Z + 240 Ohm
Input Sensitivity- 93mV (ref. 500mV out, Volume maximum)
Frequency Response- ±0.03dB (20Hz-20kHz)
Maximum voltage output IHF load- >4.5V (ref. 0.1% THD)
Tone Controls-
Treble: ±7.0dB at 20kHz
Bass: ±7.0dB at 60Hz
Balance: -10dB
Phono Input, Pre Out
THD (20Hz-20kHz)- <0.01% at 2V out
Signal to Noise Ratio-
>84dB (200 Ohm source; A-weighted, ref. 500mV out)
>76dB (MM cartridge source, IHF; A-weighted, ref. 500mV out)
Input Sensitivity- 1.44mV (ref. 500mV out, Volume maximum)
Frequency Response- ±0.3dB (20Hz-20kHz)
Maximum Input Signal at 1kHz- >80mVrms (ref. 0.1% THD)
Line Input, Headphone Out
THD (20Hz-20kHz)- <0.005% at 1V out
Signal/Noise Ratio- >110dB (32 Ohm loads; A-weighted, ref. 2V out, unity gain)
Frequency Response- ±0.3dB (20Hz-20kHz)
Channel Separation- >60dB at 1kHz
Output Impedance- 6 Ohms
General Specifications
Continuous Output Power into 4 Ohms and 8 Ohms (Stereo)- >80W (ref. 20-20kHz at rated THD, both channels driven)
Continuous Output Power into 8 Ohms (Bridge Mode)- 300W (at 20-20kHz at THD 0.03%)
THD (20Hz-20kHz)- <0.03% (250mW to 80W, 8 Ohms and 4 Ohms)
Signal to Noise Ratio- >98dB (A-weighted, 500mV input, ref. 1W out in 8 Ohms)
Clipping Power- >95W (at 1kHz 0.1% THD)
Clipping Power (Bridge Mode)- >315W (at 1kHz 0.1% THD)
IHF Dynamic Power-
8 Ohms 120W
4 Ohms 200W
2 Ohms 250W
IHF Dynamic Power (Bridge Mode)-
8 Ohms 500W
4 Ohms 560W
Peak Output Current- >20A (in 1 Ohm, 1ms)
Damping Factor- >300 (ref. 8 Ohms, 20Hz and 6.5kHz)
Frequency Response- ±0.3dB (20Hz-20kHz)
Channel Separation-
>75dB (1kHz)
>70dB (10kHz)
Input Sensitivity (for 80W in 8 Ohms)- Line In: 470mV; Digital In: 21% FS
Sample Rate- up to 24 bit/192kHz
Frequency Band- 2.402G-2.480G
Maximum Transmit Power (dBm)- 7dBm ±2dBm
Power Consumption
at Auto Standby ON and Network Standby OFF- 0.5 Watts*
at Auto Standby ON and Network Standby ON- 1.2 Watts**
OFF mode (Power switched OFF)- 0.1 Watts
* – After 20 minutes of no user interface interaction and no active source input
** – With established wireless Bluetooth connectivity and 20 minutes of no user interface interaction and no active source input
NOTE: Bluetooth connectivity is always live when configured
Weight & Dimensions
Gross Dimensions (W x H x D)*- 435 x 100 x 390mm (17 1/8 x 3 15/16 x 15 3/8)”
Net Weight- 7.8kg (17.2lb)
Shipping Weight- 10.1kg (22.3lb)
*Gross dimensions include feet, extended buttons and rear panel terminals